The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
Are you currently interested in facts about How to Install a Bathtub?
Setting up a bath tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a new one is likewise a moderately hard task. If the old tub is easily available, the task can move quickly; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub as well as embeded in the new one. See to it you have actually qualified yourself for the work and fit trying it. As opposed to employing a service provider to take over a halfway-completed project, it is much better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will assist you set up a new tub in your bathroom if you have already purchased a new tub as well as don't need to alter the plan of your previous water pipelines.
Your devices and product list should make up the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bath needs to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap features a plastic washer, it is fitted between the bath and the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps device to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom ought to now be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water system. After doing so, activate the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be fairly problematic because of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Before carrying on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Utilizing both wood boards under its feet, place the bath tub in the called for placement. The wooden boards are handy in equally spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four small factors.
The next goal is to make sure that the tub is leveled all round. This can be achieved by checking the level and readjusting the feet on the tub until the level reviews level.
To set up taps, fit all-time low of the outermost adaptable tap port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks as well as tighten them if required. Load the bathtub as well as also inspect the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bathroom paneling as described in the supplier's user's manual. Tiling and also sealing around the tub must wait till the tub has been used at the very least once as this will certainly resolve it into its last placement.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end supplies a link to the existent supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washers remain in location in between the tap and the sink. Protect the faucet in position with the producer supplied backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind ought to be linked to the faucet ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the area where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to fracture a stiff seal, triggering the water to pass through the wall between the bath and the tiling, causing difficulties with dampness and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also installations. They are offered in tubes and cartridges, as well as are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly offered on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on Installing A Bathtub? Place a short review directly below. We would be delighted to hear your insights about this blog post. We are looking forward to see you back again in the near future. Are you aware of somebody who is fascinated by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Why not promote it. Thanks so much for taking the time to read it.
24/7 emergency? We're here! Report this page